IDX HOME

CASINO HOME

WICKETS - RFID

    --   WR77 READER

    --   CARDS & TAGS

    --   TABLE TRACKER

X-Mark TOKENS

COIN ACCEPTORS

     --  X-10 Xeptor

     --  X-20 Xeptor

     --  X-50 Xeptor

     --  X-60 Xeptor

     --  X-70 Xeptor

CRAPS DISPLAY

ACCESSORIES

   --  Personality Plugs

   --  Coin Selectors

   --  X-Key, X-Tracker

   --  Xaminer

   --  XaminerPC

TECH SUPPORT

HOW TO ORDER

CONTACT US

ABOUT IDX

Google

 
  IDX   Web

 

 

Personality PlugsTM

The Xeptor Electrical Interface
Personality plugs are small connector conversion modules about as big as the last segment of your little finger. They are used to convert the 8pin header in the Xeptor to any of many available connector styles and pin assignments common in the industry. For example, there is one Personality Plug type for each of the older Coin Mechanisms CC-series acceptors and the NRI multi-wire output acceptors. Additionally, many have been designed to meet the needs of specific OEMs, including such things as simulation of OEM credit optics module signals.  Other special interface requirements are easily satisfied with new Personality Plugs designed specifically for the job. With the correct Personality Plug installed in an Xeptor, retrofit installation requires no machine connector re-wiring! The tables below can help you decide which Personality Plug to use. The electrical specification for each pin definition are found in the 3rd table below.

Personality
Plug Model:
PP16 PP16IC PP40 PP46 PP62 PP3337 PPUNI
Compatibility
Connector
CC-16
JST-6
CC-16 12V
JST-6
CC-40
JST-6
CC-46
Molex-6
CC-62
Molex-7
CC-33,-37
JST-3
Universal
JST-6
Pin 1 1K to Ground Inhibit /Tilt Inhibit Ground 24 VDC/AC Inhibit
Pin 2 Sense Sense Inhibit /Tilt /Sense Sense /Coin Optics
Pin 3 48 VDC/AC ----- /Credit /Credit /Tilt Ground -----
Pin 4 24 VDC/AC 24 VDC/AC 24 VDC/AC /Sense /Credit   24 VDC/AC
Pin 5 12 VDC 12 VDC 12 VDC 12 VDC Key Pin   -----
Pin 6 Ground Ground Ground Ground 12 VDC   Ground
Pin 7         Inhibit    

 

Personality
Plug Model:
PPNRI-6 PPNRI-3 PPIGTDC PPCDS PPSIGMA PPCWR PPMOX
Compatibility
Connector
NRI
10pin IDC
NRI
10pin IDC
IGT DC Slots
Molex-6
JST-6 Molex-7 Wires Wires
Pin 1 Ground Ground Inhibit /Tilt Ground Yel-24VAC Yel - 24VAC
Pin 2 12VDC 12VDC /Sense Inhibit Sense Red - Relay Blk - Grnd
Pin 3 /Output5 ----- ----- /Credit /Credit-A Red - Relay Wht - Inhibit
Pin 4 /Output6 ----- ----- 24VAC /Credit-B Blk - Ground Blu - /Out1
Pin 5 Coin Return ----- 12 VDC +12VDC -----   Pur - /Out2
Pin 6 Inhibit Inhibit Ground Ground +12VDC   Brn - /Out3
Pin 7 /Output1 /Output1     Inhibit    
Pin 8 /Output2 /Output2          
Pin 9 /Output3 /Output3          
Pin 10 /Output4 -----          

 

Electrical Specifications For IDX Xeptors

SIGNAL: ELECTRICAL CHARACTERISTICS 
(Note: Pulse widths programmable via "P" command on serial port)
INHIBIT Inhibit = float or >3.5VDC, Enable = < 1.0VDC
SENSE Active high 32ms pulse, PNP 12V pull-up 10mA max, 3.3K pull-down.
/SENSE Active low 32ms pulse, NPN sinking 10mA max, 47K 5V pull-up.
/CREDIT Active low 32ms pulse, NPN sinking 10mA max, 47K 5V pull-up.
/TILT Active low >32ms pulse, NPN sinking 10mA max, 47K 5V pull-up.
/OUTPUT-n Active low >32ms pulse, NPN sinking 10mA max, 47K 5V pull-up.
RELAY Relay contact terminal. 40V 0.2A peak rating..
/Coin Optics Wire-OR optics output enable, 100ms low pulse, 100K 12V pull-up.
48VDC/VAC Power input 38 to 55VDC, 38 to 55VAC, 35mA max @idle.
24VDC/VAC Power input 14 to 32VDC, 16 to 32VAC, 35mA max @idle.
12VDC Power input 11.5 to 16VDC, 25mA max @idle, 240mA accept gate.
1K to Ground 1K 1W resistor to circuit ground. (for triac holding current)
Ground Circuit common.